A lot of consumer grade routers don't support WoL from WAN. Enable it and set it up, probably easy to do. If your router supports WoL, well you should be a happy camper. #Wol wake on lan wan safe windowsLastly, go into the Power Management settings in Windows and make sure "Turn off NIC to conserve power" is disabled. The 3rd one I have set to 100Mbps, for other purposes, but you may have it set for 10Mbps ,which is ok. I have a Realtek NIC and it has 3 options for WoL: Wake from magic packet, Wake on pattern match, WoL & Shutdown Link Speed. Enable your NIC to respond to WoL "magic" packets.įor Windows, go to your NIC adapter settings, select configure>advanced, to get into your NIC's WoL settings. Go into your BIOS and in your Power Management settings, you will see the options for WoL and your NIC. I will assume that you have some basic knowledge of Windows or the OS you are using. I won't cover every detail in this guide. #Wol wake on lan wan safe PcAlso you could say, WoL is pretty useless to begin with since you have to be somewhat in the vicinity of your PC to begin with so what's the point. Unfortunately most routers, most will not let you dothat from the WAN side for security reasons and thus lies our problem. All that needs to be done, is to send a packet to the router's broadcast address, usually 192.168.1.255 or 192.168.0.255. I thought I would write this guide to help people over the hurdles of trying to wake their PC from WAN. #Wol wake on lan wan safe softwareClick OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A.I have spent all kinds of time on this over the past several weeks trying to get this working, which I did finally. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the WAN port according to the network environment. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page. #Wol wake on lan wan safe macEnter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Check if the desired IP address is reserved for PC A. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. Enable Export to DHCP Address Reservation. In the IP-MAC Binding List section, click to load the following page. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router. Make sure the WAN port of the router is routable from PC B.PC A should be powered off normally and the power supply is normal.In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet. Make sure that the network card of PC A supports WOL.In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN. Make sure that the motherboard of PC A supports WOL.It is required that PC B can wake up PC A by sending a Magic Packet via the internet.īefore configuring WOL, you should do the following preparation: In the diagram below, PC A is connected to the internet via the router. You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |